螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

轧制道次间插入冷却对特厚钢板组织与性能的影响

使用实验轧机旁冷却装置配合轧机进行轧制实验，研究轧制道次间不同冷却工艺对特厚钢板组织和性能的影响规律.研究结果表明:采用道次间冷却工艺可以在全厚度方向获得组织细化及强韧性提高效果，采用强冷道次间冷却实验钢1/4处晶粒尺寸可细化至10μm，强度为376MPa，-40℃冲击功为169J;心部晶粒尺寸可细化至15μm，强度为360MPa，-40℃冲击功为123J.本工艺可形成470μm厚表层细晶层，晶粒尺寸可细化至5μm;粗轧道次间插入冷却工艺轧制钢板强度和冲击韧性优于中间坯冷却工艺;随冷却强度增加，钢板内部组织明显细化且强度大幅提高.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

金具零部件表面防腐蚀试验研究

随着经济的持续高速增长，各行业用电需求增大。在加快特高压骨干电网建设的同时，提高现有电网的输电能力、输电质量成为重中之重。金具是海上换流站的重要组成部分，海洋环境的特殊性，对金具提出了更高的耐腐蚀性能要求。为了探究海洋环境对金具的腐蚀性，选用ZL101A和ZL102两种典型的铝合金金具，采用5种辅助防腐蚀工艺获得5种耐腐蚀样本，并模拟海上工况对其分别进行盐雾腐蚀试验，得出最优防腐蚀工艺。研究表明：ZL101A和ZL102两种铝合金具有一定的耐腐蚀性能，ZL101A铝合金的耐腐蚀性能强于ZL102铝合金的；抛丸处理的防腐措施在ZL101A铝合金样本中的防腐蚀表现要强于ZL102铝合金样本的；阳极氧化在两种材质中防腐蚀表现均为优异，是最优异的防腐蚀工艺。     

Seismites(地震岩)等术语的概念与名称

seismites,按其字面意思理应翻译成地震岩,即与地震有成因联系或受发震断裂改造、变形的岩石。按发震时地质材料的固结程度与力学性质,地震岩可分为震积岩(地震时尚未固结成岩的含水沙土层,即软沉积物)和脆性断层岩(地震时已经固结成岩的沉积岩、岩浆岩和变质岩)。脆性断层岩包括断层角砾岩、碎裂岩、超碎裂岩、假熔岩和断层泥等。发育由沙土液化形成的软沉积物变形构造的沉积岩,统称为“沙土液化岩”(liquefactites),但是长期以来一直被误译为seismites。大量的研究表明,并不是所有的沙土液化和软沉积物变形都是由地震造成的,也并不是所有地震都能导致沙土液化。只有那些所在区域存在重要发震断层、真正由地震引起的区域性的沙土液化造成的软沉积物发育变形构造的岩层才能称之为震积岩(seismic liquefactites)。震积岩不应再翻译成seismites。零星出现的软沉积物变形构造与沙土液化构造(例如:砂涌丘)不足以作为古地震的证据。     

食用蓝藻螺旋藻和葛仙米中金属元素的分析

采用硝酸和高氯酸(4∶1)混合酸消化2种可食用蓝藻螺旋藻和葛仙米,原子吸收光谱法检测螺旋藻和葛仙米中的K、Na、Mg、Ca、Zn、Fe、Cu、Mn、Cr、Pb和Cd共11种金属元素含量。结果表明,2种蓝藻中矿质元素含量均较高,特别是Ca含量高达61 905.132mg·kg~(-1);而有害重金属Cr,Po和Cd含量均远低于国家规定标准,表明这2种食用蓝藻均无重金属富集或污染。本结果显示,螺旋藻和葛仙米是极好的天然富钙营养食品,可作为人体矿质元素和微量元素缺乏症的补给品.     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。     

用增量有限元法计算金属流动

利用增量有限元理论 ,对金属材料的变形过程进行模拟。为了模拟工程中塑性变形较大的构件的变形规律 ,在每个加载步迭代完成后自动实现坐标更新。